Air Cleaners
AVO Dampers
Bafled Sumps
Bearings
Bellhousings
Block Bolts
Brackets/Mountings
Cam Followers
Camshafts
Carbs and Injection
Cobra Seats
Con-Rods
Cooling accessories
Crankshafts
Cylinder Block
Cylinder Heads
Electrical
Engine Pulley's
Exhaust Manifolds
Flywheel/Clutch
Gaskets/Seals
Gearboxes
Inlet Manifolds
Long Engines
Miscellaneous
Oil/Lubrication
Pistons/Rings
Short Motors
Stroker Crank Kits
Suspension
Turnkey Engines
Valves/Timing
Water Pumps
Home > Oil/Lubrication
You're viewing 1 - 25 of 24 products in this category
Remote Oil Filter Mtg. Kit MGB V8 Type (MOCAL)
Remote Filter kit allows fitting of filter to bulkhead or chassis rails. Eradicates problem with oil filter clearance and potential damage.

Kit features

New Cast Alloy Oil pump Base,
High Pressure Hoses with swagged ends
Unions & Dowty seals
Cast Filter head
Fitting Instructions
more >>
SD1 > Oil Filter
138mm Length for SD1 Engine
more >>
Rover V8 SD1 > Oil pump gear/shaft
Oil Pump Gear Set for SD1 V8 Engine 1976 >

The Rover V8 Engine has an inherently poor lubrication system especialy if used at higher rpm.
To help maintain oil pressure repace worn or chipped gears with new items when rebuilding.
Can not be used with early P5B/P6 Timing cover
(OE Parts)
more >>
Oil Pump Idler Gear SD1
more >>
SD1 oil Pump base ( Remote Type)
Oil Pump base to suit either remote filter or oil cooler
more >>
SD1 High pressure Releif Valve+Spring
Boosts Oil pressure by 10+PSi throughout Range.

Also suitable for
Land Rover Discovery 3.5,3.9,Non Serp
Range Rover 3.5 Carb/Efi, 3.9 & 4.2 Non Serp
Morgan + 8 >1994
TVR Chimera, Griff, Wedge >1994
more >>
Budget Rover V8 Rocker Shaft+Steel Rocker Arm Set
Budget HD Steel rocker Arm Sets - use standard shafts and pedestals.

Made in China -

Strong rocker arms but heavier than standard aluminium type. Unlikely to fail in service as rocker pad is an integral part of the casting unlike the OEM original items. The OEM type are incidently 640 + VAT......
more >>
Rover SD1/SBF Oil Filter (short)
The Shortest Filter available - for where there are clearance issues and filter is for example close to front cross member or chassis rails .

To suit Sd1 engines
Depth 4.055"
more >>
Remote Oil Filter Mtg. Kit Rover V8 1976>
This kit uses a sandwich plate for the oil pipe take-off instead of the replacement oil pump cover housing.

To suit 1976 Rover V8 SD1 and Land/Range Rover Engines with 3/4" UNF Oil Filter Threads

Supplied complete with swaged straight and 90 degree High Pressure nitrile rubber hoses,
Sandwi......
more >>
Oil Coolers
Oil Cooler Cores available in a variety of core sizes - please enquire for your application.
more >>
Oil Cooler Mounting Kits (Steel Braided Hose)
Oil Cooler Mounting Kits with braided steel hoses for Custom or Motorsport Applications.

Custom lenght hoses and fittings also supplied
more >>
Oil Cooler Mounting Kits (Rubber Hose)
Oil Cooler Mounting Kits with rubber hose for most applications. The rubber hoses have swaged steel ends usualy with a 90 degree fitting.

Hoses can be supplied overlong to suit your application.

Please enquire for further details.
more >>
Rover Rocker Shafts and Alloy Rocker Arm Set
Pair of Standard Rocker Shafts(aftermarket)

Set of 16 Alloy Left and Right Handed Rocker Arms. Non Genuine

Image is for representation only.
more >>
Rover V8 P5b/P6 Range Rover High Pressure & Volume Oil Pump Kit
The pre 1976 Rover V8 engines often suffered from a low oil pressure problem both @ idle speed and at higher engine rpm.
This kit will increase idle pressure by approx 15 psi and raise volume by 40 %.

To suit
Rover P5B
Rover P6
Range Rover Classic >1976
Land Rover > 1976
MGB V8
Morgan + ......
more >>
Rover V8 Engines Oil Pick Up Pipe Strainer
New Strainer Mesh to suit all Rover V8 Engines
1970 - 1994 approx 4.0" OD
more >>
Replacement Oil Pump Gears for Rover V8, TVR Serp 1994 >
Replacement Oil Pump Gear Set for serpentines belted timing covers.

OEM ( UK Made)

To Suit
TVR Chimera + Griff 1995 >
Land Rover Discovery 1994 >
Range Rover 4.0/4.6 1994 - 2002
more >>
Rover V8 Oil Pump Gear Set 1976 - 1994 ( Genuine)
Oil Pump Gear Set includes
Oil Pump Idler Gaer
Oil Pump Gear & Shaft
Shaft has male "tang" to mate up with the distributor gear/coumpling.
Gears are 26.5mm/1.043" thickness.
These are Genuine Land Rover Parts
more >>
Oil Pump Gears 3.5,3.9,4.2 Sd1, Morgan, TVR Land Rover etc
Oil Pump Gear Set for SD1 V8 Engine 1976 >

The Rover V8 Engine has an inherently poor lubrication system especialy if used at higher rpm.
To help maintain oil pressure repace worn or chipped gears with new items when rebuilding.
Can not be used with early P5B/P6 Timing cover
more >>
Oil Filter Genuine Land Rover
Genuine Land Rover ( Best Quality( Oi Filter

To Suit

Rover Sd1, TVR, Morgan all V8 engines
From 1976 - 2002
more >>
Remote Oil Filter Mounting Kit Rover V8 before 1976
This kit uses a sandwich plate for the oil pipe take-off instead of the replacement oil pump cover housing.

To suit pre 1976 Rover V8 and Land Rover Engines with 13/16 UNF Oil Filter thread

Supplied complete with swaged straight and 90 degree High Pressure nitrile rubber hoses,
Sandwich pla......
more >>
Rover P5B, P6 Oil Filter
FRAM Oil Filter - 4" lenght

Rover P5b
Rover P6
MGB V8 and Early Morgan +8 ( check)
more >>
Rover V8 Serpentine Cover Pressure Releif Valve Kit
Replacment Oil Pressure Releif Valve Kit.
OEM Original supplier to Land Rover

Includes :
New Valve Cap/Bung machined from Alloy
Replacment Valve
Replacment Spring
"o" Ring Seal for Cap/Bung

Suitable for ALL Sepentine Belted Engines
TVR 1996 - 4.0,4.5,5.0
Land Rover Discovery 2 4.0
Ran......
more >>
V8 Serpentine Engines Serp Timing Cover Rebuild Kit
Serpentine Engines :
TVR 1996 >
Discovery 1
Range Rover P38 1996 - 2002

Kit comprises -
Replacement Made in the EU Cenrifugal Oil Pump Gears
Replacment Oil Pressure Releif Valve, Spring, Cap and "O" Ring
more >>
Rover, TVR Morgan Remanufactured Oil Pump Base Housing
Remanufactured Oil Pump Base unit for Rover V8 engines

1976 - 1992

Remanufactured Oil Pump Cover Housing.
Fully Inspected for defects, machined, cleaned and valve bore honed to ensure free movment of valve. Supplied with new valve and spring ( uprated spring also available at extra cost)
more >>
© Abbey Sportcars Ltd.   |   Company No. 03916786   |   VAT No. 858100630   |